TDS-AQUAFIN-TC150AL_041024.pdf
4 Pages
837 KB
Download
<h1>TDS-AQUAFIN-TC150AL_041024.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>AQUAFIN-TC150AL</p> <p>1-component, moisture cured, aliphatic, polyurethane elastomeric waterproof top coating <br />CSI Div. 07 & 09 <br />07 14 16 Cold Fluid Applied Waterproofing <br />07 18 00 Traffic Coatings <br />07 18 13 Pedestrian Traffic Coatings <br />07 18 16 Vehicular Traffic Coatings <br />09 01 90 Maintenance of Painting and Coating <br />Product Description: <br />AQUAFIN-TC150AL is a single component, liquid applied, moisture cured, <br />aliphatic, polyurethane elastomeric waterproof coating. It can be used as <br />a top layer over VAPORTIGHT COAT®-SG3 and AQUAFIN-TC100M <br />and is also part of the TC 400 - 4 Coat System and the TC 500 - 5 Coat <br />System. <br />Typical Applications: <br />• When used as a top coat in conjunction with AQUAFIN-TC100M (as <br />the base coat), or as part of the TC 400 - 4 Coat System: Interior and <br />exterior concrete walkways, patios, balconies, breezeways, building <br />entrance areas, and stairways. <br />• When used as a protective top layer over VAPORTIGHT COAT-SG3: <br />Interior and exterior pedestrian floor areas including: on grade, above <br />and below grade concrete as well as split slabs. <br />•W <br /> hen used as part of the TC 500 - 5 Coat System: Concrete parking <br />garage decks, turn lanes, and ramps. <br />Advantages: <br />• Moisture cured <br />• UV stable <br />• Good color retention <br />• Seamless waterproofing membrane <br />• Single component - easy to apply <br />Substrate Preparation: <br />• All surfaces must be sloped according to industry standards to facilitate <br />water removal. All water must drain and/or evaporate within 48 hours. <br />• AQUAFIN-TC150AL can be placed directly over AQUAFIN-TC100M, <br />AQUAFIN-TC125, or Aquafin’s VAPORTIGHT COAT®-SG3 without an <br />additional primer. Refer to the respective product Technical Data Sheet <br />for proper surface preparation, installation instructions, and cure times. <br />Pay attention to recoat times and application windows. Ensure surface of <br />preceding coat (base coat, intermediate coat, or epoxy vapor barrier) is <br />dry, clean and free from any bond inhibiting materials such as dust, dirt, <br />sand, etc. <br />• Expansion and control joints are to be prepared in accordance with <br />project specifications. <br />Jobsite Preparation: <br />• Only proceed with application when ambient and surface temperatures <br />are minimum 50°F (10°C) and rising, and more than 6°F (3°C) above <br />dew point. Temperatures must be maintained within this range for at <br />least 24 hours after the installation. Do NOT proceed with application <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical and Technical Data AQUAFIN-TC150AL <br />Hardness, (ASTM D2240):</p> <p>90 ± 5 Shore A</p> <p>Tear Resistance, Die C, <br />(ASTM D624):</p> <p>400 ± 50 pli <br />70.1 ± 8.8 kN/m</p> <p>Tensile Strength, (ASTM D412):</p> <p>2700 ± 200 psi <br />18.6 ±1.4 MPa</p> <p>Ultimate Elongation, (ASTM D412):</p> <p>250 ± 50% psi</p> <p>Specific Gravity:</p> <p>1.20 ± 0.4</p> <p>Solids by Weight, (ASTM D2369):</p> <p>80 ± 5%</p> <p>Solids by Volume, (ASTM D2697):</p> <p>74 ± 3%</p> <p>Viscosity at 75°F (24°C):</p> <p>1500 ± 300 cps</p> <p>Volatile Organic Compounds, <br />(ASTM D2369):</p> <p><2.08 lb/gal <br /><250 gm/liter</p> <p>All data are based on tests performed under laboratory conditions unless <br />otherwise stated. In practice, climatic variations such as temperature and humidity, <br />may affect these values.</p> <p>when the temperatures drop below 50°F (10°C) or if precipitation is <br />imminent. Special precautions are to be taken when ambient and/or <br />substrate temperatures are approaching, at, or above 90°F (32°C) <br />and it may be necessary to limit material application to evening hours for <br />exterior exposed decks. <br />• Hot surfaces should be cooled and shaded while cold surfaces should <br />be heated and sheltered. <br />Mixing: <br />• Use chemical resistant (Nitrile) gloves and goggles when mixing or <br />applying AQUAFIN-TC150AL. <br />• For ease of mixing and placement, the temperature of the material <br />should be between 70°F to 80°F (21°C to 27°C). <br />• Open container and mix for 1 - 2 minutes until streak free mixture is <br />obtained. Thoroughly scrape sides of pail as material is mixed. Boxing <br />material is recommended to ensure color uniformity. <br />• Use caution not to whip air into the material as this may result in pinhole <br />blisters and/or shortened pot life. Do not mix in an up and down motion. <br />Installation: <br />Read all instructions thoroughly prior to installation. <br />• Codes and regulations will vary between cities, counties, municipalities, <br />states and federal divisions. Refer to project drawings and specifications <br />and always follow all applicable codes and requirements. <br />• When the application calls for TC 400 or TC 500, all layers in the <br />4 Coat or 5 Coat System may be required. This includes the use of <br />PRO-Tekt SP (Sealant Primer), even if concrete surface conditions do not <br />appear to warrant the use of a primer. See illustrations and chart located <br />at the bottom of page 4 of this Technical Data Sheet. <br />• For best results, apply AQUAFIN-TC150AL using a notched squeegee <br />Page 1 of 4</p> <p>(04/10/24 - EKJWAC)</p> <p>AQUAFIN-TC150AL <br />or a notched trowel. A phenolic resin core roller may be used but extra <br />care should be taken not to trap air which may result in bubbles. <br />• Apply AQUAFIN-TC150AL in a continuous coating (wet on wet) <br />application to minimize lines and/or streaking. <br />• For warm weather applications [above 75°F (24°C)], keep product <br />containers out of direct sunlight. <br />Notes: Always verify that the proper WFT (wet film thickness) has been <br />achieved by measuring each coat using a wet film gauge. As a minimum, it <br />is recommended to check the mil thickness in every corner, plus the center <br />areas of the application area. Large areas will require many check points. <br />When applying multiple, thinner coats, verify that the total DFT (dry film <br />thickness) meets the stated requirements. See coverage chart for minimum <br />WFT mil guidelines and DFT mil requirements. <br />Single Coat Pedestrian Applications where UV Stability is <br />required: <br />• Base <br />Base Coat: Apply AQUAFIN-TC100M at a rate of 85 – 100 ft2 per <br />gal (2.0- 2.4 m2 per liter) to achieve a minimum of 16 mils WFT (wet film <br />thickness) [12 (± 2) mils DFT (dry film thickness)]. <br />• Allow base coat of AQUAFIN-TC100M to cure [typically16 hours at <br />75°F (24°C) and 50% relative humidity]. <br />• Top Coat: Apply AQUAFIN-TC150AL within 36 hours at a rate of 85 – <br />100 ft2 per gal (2.0 - 2.4 m2 per liter) to achieve a minimum of 16 mils <br />WFT [12 (± 2) mils DFT]. <br />• Immediately (within 2 minutes) after application, broadcast Aquafin <br />Coated Quartz Sand at a rate of 10 - 20 lbs/100 ft2 (0.5 - 1.0 kg/ <br />m2) or as required to achieve a slip-resistant finish and immediately <br />backroll sand into the wet coating so that the sand is fully encapsulated. <br />The aggregate should be applied vertically, allowing it to fall onto the <br />AQUAFIN-TC150AL. As a second option, clean, dry, washed, oven <br />dried, rounded sand, 16 - 20 mesh (0.84 - 1.19 mm), 6.5+ Mohs <br />minimum hardness can also be used for the sand broadcast. <br />• Total System Thickness: 32 mils WFT + 15 mils due to sand aggregate <br />broadcast (20 to 28 mils DFT + 15 mils sand). <br />Double Top Coat Pedestrian Applications where UV <br />Stability is required: <br />• Base <br />Base Coat: Apply AQUAFIN-TC100M at a rate of 85 – 100 ft2 per <br />gal (2.0 - 2.4 m2 per liter) to achieve a minimum of 16 mils WFT (wet <br />film thickness) [12 (± 2) mils DFT (dry film thickness)]. <br />• Allow base coat of AQUAFIN-TC100M to cure [typically16 hours at <br />75°F (24°C) and 50% relative humidity]. <br />• First Top Coat: Apply AQUAFIN-TC100M first top coat within 36 hours <br />at a rate of 85 – 100 ft2 per gal (2.0 - 2.4 m2 per liter) to achieve <br />a minimum of 16 mils WFT [12 (± 2) mils DFT]. Do not apply sand <br />broadcast. <br />• Second Top Coat: Apply AQUAFIN-TC100M second top coat within <br />36 hours at a rate of 85 – 100 ft2 per gal (2.0 - 2.4 m2 per liter) to <br />achieve a minimum of 16 mils WFT (wet film thickness) [12 (± 2) mils <br />DFT (dry film thickness)]. <br />• Immediately (within 2 minutes) after application, broadcast Aquafin <br />Coated Quartz Sand at a rate of 10 - 20 lbs/100 ft2 (0.5 - 1.0 kg/ <br />m2) or as required to achieve a slip-resistant finish and immediately <br />backroll sand into the wet coating so that the sand is fully encapsulated. <br />The aggregate should be applied vertically, allowing it to fall onto the <br />AQUAFIN-TC150AL. As a second option, clean, dry, washed, oven <br />dried, rounded sand, 16 - 20 mesh (0.84 - 1.19 mm), 6.5+ Mohs <br />minimum hardness can also be used for the sand broadcast. <br />• Total System Thickness: 48 mils WFT + 15 mils due to sand aggregate <br />broadcast (30 to 42 mils DFT + 15 mils sand). <br />Note: A double coat application of AQUAFIN-TC150AL will increase the <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>longevity and overall performance of the coating system. <br />Two Coat Pedestrian Applications over VAPORTIGHT <br />COAT®-SG3: <br />• P rimer & Vapor Barrier: Apply VAPORTIGHT COAT®-SG3 at a rate of <br />100 ft2 per gal (2.45 m2 per liter) to achieve a minimum of 16 mils WFT. <br />Refer to current VAPORTIGHT COAT®-SG3 Technical Data Sheet for full <br />mixing and application instructions, and other important information. Pay <br />close attention to recoat times. <br />• First Coat: Apply AQUAFIN-TC150AL first coat within 48 hours at a rate <br />of 85 – 100 ft2 per gal (2.0 - 2.4 m2 per liter) to achieve a minimum of <br />16 mils WFT (wet film thickness) [12 (± 2) mils DFT (dry film thickness)]. <br />• Second Coat: Apply AQUAFIN-TC150AL second coat within 36 hours <br />at a rate of 85 – 100 ft2 per gal (2.0 - 2.4 m2 per liter) to achieve a <br />minimum of 16 mils WFT (wet film thickness) [12 (± 2) mils DFT (dry film <br />thickness)]. <br />• Immediately (within 2 minutes) after application, broadcast Aquafin <br />Coated Quartz Sand at a rate of 10 - 20 lbs/100 ft2 (0.5 - 1.0 kg/ <br />m2) or as required to achieve a slip-resistant finish and immediately <br />backroll sand into the wet coating so that the sand is fully encapsulated. <br />The aggregate should be applied vertically, allowing it to fall onto the <br />AQUAFIN-TC150AL. As a second option, clean, dry, washed, oven <br />dried, rounded sand, 16 - 20 mesh (0.84 - 1.19 mm), 6.5+ Mohs <br />minimum hardness can also be used for the sand broadcast. <br />• Total System Thickness: 48 mils WFT + 15 mils DFT due to sand <br />aggregate broadcast (36 to 44 DFT + 15 mils sand). <br />TC 400 - 4 Coat System and TC 500 - 5 Coat System: <br />Refer to current AQUAFIN-TC125 Technical Data Sheet for layer-bylayer application instructions. See page 4 of this Technical Data Sheet for <br />guidance in layering sequence. <br />Protection and Curing: <br />• Allow at least 96 hours [based on 75°F (24°C) and 50% relative <br />humidity] before permitting pedestrian traffic on the finished surface after <br />application of AQUAFIN-TC150AL as the final top coat. <br />• Allow at least 120 hours [based on 75°F (24°C) and 50% relative <br />humidity] before permitting vehicular traffic on the finished surface after <br />application of AQUAFIN-TC150AL as the final top coat (as part of the <br />TC 500 - 5 Coat System). <br />• AQUAFIN-TC150AL is sensitive to heat and moisture. Higher ambient <br />or higher surface temperatures, or high humidity will accelerate the cure <br />time. Cooler ambient or cooler surface temperatures, or low humidity will <br />extend the curing time. <br />Care and Maintenance: <br />• A weekly cleaning routine is recommended for busy areas and will help <br />extend the life of the pedestrian traffic coating system. <br />• Sweep or vacuum the top surface, and then clean it with a wet mop. <br />• For occasional heavy cleaning, the use of a pressure washer (maximum <br />1,000 psi) is recommended along with a low suds, bio degradable <br />detergent. It is important to thoroughly rinse the area and remove all <br />traces of residue and detergent to prevent a slipping hazard. <br />• Solvent-based cleaners may cause damage to the pedestrian traffic <br />coating system and are not recommended. <br />• Leaves, rusted metal, soil from plants, and other stain-causing materials <br />can result in permanent discoloration to the top coat of the pedestrian <br />traffic coating system. See Recoating and Repairs section below when <br />staining has occurred. <br />Recoating and Repairs: <br />• Inspect the surface of the pedestrian traffic coating periodically, and <br />Page 2 of 4</p> <p>(04/10/24 - EKJWAC)</p> <p>AQUAFIN-TC150AL <br />look for signs of wear and damage to the top coat. <br />• When occasional recoating of the AQUAFIN-TC150AL top coat is <br />needed, follow the procedure below. <br />1. Pressure-wash the existing surface of AQUAFIN-TC150AL top coat with <br />water to clean and remove all foreign matter, dirt, debris and any loose <br />coating. <br />2. Allow area to dry completely. <br />3. Apply Aquafin RE-ROOF Primer PO in a monolithic application at a rate <br />of 100 - 200 ft² per gal (2.5 to 4.9 m2 per liter) to achieve a minimum <br />of 5 mils (0.1 mm) WFT (wet film thickness). <br />4. Allow RE-ROOF Primer PO to cure (to touch) until no longer tacky. <br />5. Once RE-ROOF Primer PO is tack-free, apply AQUAFIN-TC150AL to <br />the primed area within 12 hours. Apply AQUAFIN-TC150AL at a rate <br />of 85 – 100 ft2 per gal (2.0 - 2.4 m2 per liter) to achieve a minimum of <br />16 mils WFT (wet film thickness) [12 (± 2) mils DFT (dry film thickness)]. <br />6. Allow recoat of AQUAFIN-TC150AL to cure [typically16 hours at 75°F <br />(24°C) and 50% relative humidity] and protect the area from pedestrian <br />traffic for at least 48 hours. <br />7. Refer to the current RE-ROOF Primer PO and AQUAFIN-TC150AL <br />Technical Data Sheets for additional surface preparation, mixing and <br />application instructions. <br />Note: If damage has occurred below the top coat layer of the pedestrian <br />traffic coating system, contact Aquafin Technical Department or your local <br />Aquafin Representative for repair recommendations. <br />Clean-up: <br />Immediately clean all equipment and tools with polyurethane-grade solvent <br />(alcohol free). <br />Limitations: <br />• Do not thin AQUAFIN-TC150AL with solvents or dilute in any manner. <br />• High temperatures/high humidity will result in shortened working times. <br />• Contact Aquafin Technical Department or your local Aquafin <br />Representative for guidance in jobsite conditions outside the stated limits. <br />• Once containers have been opened, use material as soon as possible. <br />• Color may vary due to batch-to-batch variation, always “box” different <br />batches to avoid it. <br />• Do not use over split slabs except when applying AQUAFIN-TC150AL <br />over VAPORTIGHT COAT®-SG3 as a moisture mitigation barrier. <br />• Do not use AQUAFIN-TC150AL on applications including buried <br />membrane, sandwich slabs with insulation, slabs over unvented metal <br />pan, magnesite and non-structural lightweight concrete. Contact Aquafin <br />Technical Department with questions. <br />• Pedestrian traffic coating systems are not replacements for proper <br />repairs on damaged, deteriorated, or cracked concrete structures. <br />• If concrete repairs are needed, consult a licensed Engineer and ask an <br />Aquafin Representative about Aquafin concrete repair products. <br />• Not recommended as a substitute for roofing over occupied space.</p> <p>expected to follow ICRI and ACI guidelines as well as other applicable <br />industry standards. Aquafin personnel or representatives are not site <br />inspectors or construction project managers and therefore do not approve <br />surface preparation, mixing, or application of Aquafin products. Site visits <br />by Aquafin personnel or representatives are solely for the purpose of <br />making technical recommendations, not for providing supervision or quality <br />control. <br />Colors: <br />• AQUAFIN-TC150AL is available in a Light Gray or Tan color. <br />Packaging: <br />• 5 gal pail (18.9 liters) <br />• 50 gal drum (189 liters) <br />NOTE: Sand is sold separately and is not included in kits. <br />Storage and Shelf Life: <br />Storage: Store material between 60°F to 90°F (16°C to 32°C) in a dry <br />environment and out of direct sunlight. <br />Shelf Life: 1 year in original unopened container.</p> <p>STAN</p> <p>General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time of <br />printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect final results. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN.</p> <p>LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed, or implied as to any specific methods of application or use of the product. <br />We do STONE <br />not guarantee <br />compatibility of Aquafin products with other brands. <br />For thisGRAY <br />GRAY <br />DOLPHIN <br />reason, we strongly recommend application of a sample area at the jobsite to help <br />determine suitability with other products. AQUAFIN INC. MAKES NO WARRANTY <br />AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND <br />THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED. <br />AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defective product must <br />be filed within 30 days of discovery of a problem and must be submitted with written <br />proof of purchase.</p> <p>STANDARD COLOR CHART</p> <p>Note: <br />Proper application is the sole responsibility of the user. Applicators are</p> <p>For Professional Use Only.</p> <p>The following colors are available:</p> <p>STONE GRAY</p> <p>DOLPHIN <br />GRAY <br />Light <br />Gray</p> <p>TAN <br />Tan</p> <p>BATTLESHIP GRAY</p> <p>INDIAN SAND</p> <p>Color Chart is a representation of the actual color only. Every effort has been made to reproduce these color samples as faithfully as possible. Color variations between batches may exist. Colors <br />may vary due to differences in surface texture, lighting, and methods of application. When ordering additional products make sure you use the same batch number. You will find the batch number on <br />the product label. Not all colors are always available. Contact Aquafin with questions regarding colors prior to ordering any materials or starting a project.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 3 of 4</p> <p>(04/10/24 - EKJWAC)</p> <p>AQUAFIN-TC150AL <br />System Build-Up Options: <br />Single Top Coat Pedestrian <br />Applications where UV Stability <br />is required:</p> <p>AQ</p> <p>cast <br />FIN <br />QUA</p> <p>A</p> <p>+B <br />0AL</p> <p>cast</p> <p>L <br />50A <br />-TC1 <br />N <br />I <br />F <br />A <br />0M <br />AQU <br />C10 <br />IN-T <br />F <br />A <br />AQU</p> <p>TC 400 4 Coat System <br />AL</p> <p>AF <br />AQU</p> <p>+B <br />0AL</p> <p>C15</p> <p>IN-T</p> <p>AF <br />AQU</p> <p>A</p> <p>G3</p> <p>AT-S</p> <p>O <br />HT C</p> <p>IG</p> <p>ORT</p> <p>AL</p> <p>C150</p> <p>FIN-T</p> <p>L</p> <p>50A</p> <p>-TC1</p> <p>FIN <br />QUA</p> <p>VAP</p> <p>TC 500 5 Coat System</p> <p>150 <br />IN-TC</p> <p>cast</p> <p>road</p> <p>5</p> <p>-TC1</p> <p>M</p> <p>00 <br />-TC1</p> <p>IN</p> <p>AF <br />AQU</p> <p>Two Coat Pedestrian Applications over <br />VAPORTIGHT COAT®-SG3:</p> <p>road</p> <p>oad</p> <p>Br <br />AL +</p> <p>50</p> <p>TC1</p> <p>INUAF</p> <p>Double Top Coat Pedestrian <br />Applications where UV Stability is <br />required:</p> <p>st <br />adca <br />t <br />dcas <br />FIN <br />Broa <br />A <br />+ <br />U <br />25 <br />AQ <br />0M <br />-TC1 <br />) <br />C10 <br />AFIN <br />U <br />mer <br />Q <br />IN-T <br />F <br />A <br />t Pri <br />A <br />n <br />U <br />a <br />l <br />Q <br />A <br />Sea <br />SP ( <br />Tekt <br />O <br />PR</p> <p>A <br />AQU</p> <p>t <br />dcas</p> <p>oa <br />+ Br <br />125 <br />C <br />-T <br />0M <br />r) <br />AFIN <br />C10 <br />IN-T <br />rime <br />AQU <br />F <br />A <br />nt P <br />U <br />a <br />l <br />Q <br />a <br />A <br />Se <br />SP ( <br />Tekt <br />O <br />PR</p> <p>25 <br />-TC1</p> <p>+ Bro</p> <p>AQUAFIN-TC150 AL - Application Rates for System Build-Up Layers: <br />Heavy Vehicular <br />Traffic</p> <p>Pedestrian Traffic <br />Single Top Coat <br />AQUAFIN-TC150AL <br />over <br />AQUAFIN-TC100M:</p> <p>Double Top Coat <br />AQUAFIN-TC150AL <br />over <br />AQUAFIN-TC100M:</p> <p>Two Coat <br />AQUAFIN-TC150AL <br />over VAPORTIGHT <br />COAT-SG3:</p> <p>1st BASE COAT: AQUAFINLayer TC100M at 85 - 100 sq. ft. per</p> <p>BASE COAT: AQUAFINTC100M at 85 - 100 sq. ft. per <br />gal / 16 WFT [12 (± 2) DFT]</p> <p>2nd TOP COAT: AQUAFIN-TC150AL <br />Layer at 85 - 100 sq. ft. per gal / 16 <br />3rd <br />Layer</p> <p>gal / 16 WFT [12 (± 2) DFT]</p> <p>WFT [12 (± 2) DFT] + Coated <br />Quartz Sand</p> <p>TC 400 4 Coat System</p> <p>TC 500 - 5 Coat <br />System</p> <p>PRIMER/VAPOR BARRIER: <br />VAPORTIGHT COAT-SG3 at 100 <br />sq. ft. per gal / 16 WFT</p> <p>PRIMER: PRO-Tekt SP (Sealant <br />Primer) at 300 sq. ft. per gal <br />/ 4 DFT</p> <p>PRIMER: PRO-Tekt SP (Sealant <br />Primer) at 300 sq. ft. per gal / <br />4 DFT</p> <p>1ST TOP COAT: AQUAFINTC150AL at 85 - 100 sq. ft. per <br />gal / 16 WFT [12 (± 2) DFT]</p> <p>1ST COAT: AQUAFIN-TC150AL <br />at 85 - 100 sq. ft. per gal / 16 <br />WFT [12 (± 2) DFT]</p> <p>BASE COAT: AQUAFINTC100M at 40 - 50 sq. ft. per <br />gal / 32 WFT [23(± 2) DFT]</p> <p>BASE COAT: AQUAFIN-TC100M <br />at 40 - 50 sq. ft. per gal / 32 WFT <br />[23(± 2) DFT]</p> <p>2ND TOP COAT: AQUAFINTC150AL at 85 - 100 sq. ft. per <br />gal / 16 WFT [12 (± 2) DFT] + <br />Coated Quartz Sand</p> <p>2ND COAT: AQUAFIN-TC150AL <br />at 85 - 100 sq. ft. per gal / 16 <br />WFT [12 (± 2) DFT] + Coated <br />Quartz Sand</p> <p>INTERMEDIATE COAT: <br />AQUAFIN-TC125 at 85 - 100 <br />sq. ft. per gal / 16 WFT [12 (± <br />2) DFT] + Sand Broadcast</p> <p>1ST INTERMEDIATE COAT: <br />AQUAFIN-TC125 at 70 - 83 sq. ft. <br />per gal / 19 WFT [14 (± 2) DFT] <br />+ Sand Broadcast</p> <p>TOP COAT: AQUAFINTC150AL at 85 - 100 sq. ft. per <br />gal / 16 WFT [12 (± 2) DFT]</p> <p>2ND INTERMEDIATE COAT: <br />AQUAFIN-TC125 at 70 - 83 sq. ft. <br />per gal / 19 WFT [14 (± 2) DFT] <br />+ Sand Broadcast</p> <p>4th <br />Layer <br />5th <br />Layer</p> <p>TOP COAT: AQUAFIN-TC150AL <br />at 85 - 100 sq. ft. per gal / 16 <br />WFT [12 (± 2) DFT]</p> <p>Notes: Application rates and yield values are approximate. Actual coverage may vary due to substrate variances. Failure to achieve the required DFT will compromise the effectiveness of the <br />product and void the warranty. It is the applicator’s responsibility to verify that the required dry mil thickness has been attained. Applications with broadcast do not include sand aggregate in the <br />DFT measurement. The required DFT must be achieved neat. The sand aggregate broadcast will add additional thickness. WFT (wet film thickness) and DFT (dry film thickness) requirements are <br />provided in mils.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Page 4 of 4</p> <p>(04/10/24 - EKJWAC)</p>
