TDS-ELASTOSEAL-ROLLER-BRUSH_08232016.pdf
2 Pages
408 KB
Download
<h1>TDS-ELASTOSEAL-ROLLER-BRUSH_08232016.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>ELASTOSEAL-Roller/Brush <br />Cold Fluid-Applied Rubber Membrane System <br />CSI Div. 07 <br />07 14 16 Cold Fluid Applied Waterproofing</p> <p>Technical Properties: <br />Physical state</p> <p>Liquid</p> <p>LEED Points</p> <p>Color</p> <p>brownish-black</p> <p>Hydrostatic resistance <br />(ASTM 5751-00)</p> <p>>350 psi Positive and <br />negative side</p> <p>Resistance to puncture <br />(ASTM E154-99 Section10)</p> <p>>34 N</p> <p>Elongation at break @ -5.6°C <br />(ASTM D412-98a (2000))</p> <p>480%</p> <p>Elongation at room temperature <br />(ASTM D412-98a (2000))</p> <p>1200%</p> <p>Low temperature brittleness @ 15°C (ASTM <br />D746-04)</p> <p>Passed</p> <p>Low temperature flexibility (ASTM D197001)</p> <p>Passed</p> <p>Water absorption (ASTM D570-98)</p> <p><1.4</p> <p>Perm Rating (ASTM E96)</p> <p>0.12 grains/hr ft2</p> <p>Fire rating (ASTM E109-94)</p> <p>Class C</p> <p>MR Credit 5.1, Regional Materials..........................Up to 2 Points <br />IEQ Credit 4.2, Low-Emitting Materials Paints and Coatings...1 Point <br />Using this AQUAFIN product can help contribute to LEED certification of projects in the <br />categories shown above.</p> <p>Product Description: <br />ELASTOSEAL-Roller/Brush is a ready to use fast setting, cold applied, <br />modified asphalt emulsion system using exact formulated polymers <br />providing unique elastomeric performance. It can be installed where <br />solvents and heat are not allowed. Its formulation is designed for one-coat, <br />seamless applications by roller or brush. <br />Typical Applications: <br />• Below grade, concrete or CMU exterior foundations <br />• Primary and secondary containment tanks <br />• Water fountains, ponds and water features <br />• Waste water treatment tanks and reservoirs <br />• “Sandwich slab” construction <br />Advantages: <br />• Zero VOC’s <br />• No “hot pots” or trailers <br />• Cost Efficient – reduced application times <br />• One component, ready to use <br />• 1200% Elongation <br />• Self-healing <br />• Monolithic without seams <br />• Resistant to many chemicals (contact Aquafin for complete listing) <br />Substrate Preparation: <br />• Substrates must be free of all dirt, dust, grease, oil, sealers, curing <br />compounds, form release agents, laitance and loose toppings. <br />• Only proceed with application when the temperatures remain between <br />40°F and 90°F (4°C and 32°C) and protect from freezing for 24 <br />hours after application. <br />• All surfaces to be coated should be dry (damp is acceptable with no <br />standing water). Hot surfaces should be cooled and shaded while cold <br />surfaces should be heated and sheltered. <br />• For proper adhesion, concrete substrates must have a minimum CSP−3 <br />Concrete Surface Profile as per ICRI Guideline No. 310.2-1997 <br />(Formerly Guideline No. 03732). <br />• All loose particles and/or flaking coatings must be removed by <br />sandblasting, water-blasting or other mechanical means. <br />• All detail work and tape application must be completed before <br />application of membrane can be started. <br />Mixing: <br />For best results, mechanically mix at slow speed with a 3/4” drill and <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>All data are averages of several tests under laboratory conditions. In practice <br />climatic variations such as temperature, humidity, and porosity of substrate may <br />affect these values.</p> <p>Packaging & Coverage Rate: <br />Available in 5 gal pails. <br />5 gal pail yields approx. 125 ft2 @ 60 mils. DFT</p> <p>mixing paddle. Mix at slow speeds (not exceeding 500 rpm) to prevent <br />entraining air for a minimum 15 minutes for a 5 gallon pail, and 5 minutes <br />for a 1 gallon can. <br />Application: <br />Read all instructions thoroughly prior to installation. <br />• Ensure substrate and ambient temperatures are between 40°F and <br />95°F (4°C and 35°C) before application. Do not apply if freezing <br />temperatures are expected within 24 hours. <br />ELASTOSEAL-Roller/Brush can be applied using a min. 3/4“ nap paint <br />roller or industrial paint brush. Apply by roller or brush at a rate of 50 ft2 <br />per gallon (30 mils). Apply in two coats to achieve 60 mils total thickness. <br />To apply using an appropriate spray pump consult with Aquafin Technical <br />Department. <br />Coverage: ~25 ft2/gal @ 60 mils DFT <br />Curing: <br />ELASTOSEAL-Roller/Brush will begin curing immediately upon application. <br />Full cure occurs within 72 hours at 70°F (21°C) with a relative humidity of <br />50%. Humidity can significantly impact cure times. <br />Page 1 of 2</p> <p>(updated 08/23/2016 BE/EK)</p> <p>ELASTOSEAL-ROLLER/BRUSH <br />Limitations: <br />• Do not bridge moving cracks or joints larger than 1/16”. Use “tape <br />and seal” method. <br />• Do not add admixtures or extend with aggregate. <br />• Protect from freezing for 24 hours after application. If product freezes <br />before full cure it may become necessary to recoat if cracking occurs <br />within the membrane. <br />Clean-up: <br />Promptly wash hands with baby oil. Clean tools and equipment with <br />Mineral Spirits before material dries. Cured material must be removed <br />mechanically. <br />Packaging: <br />ELASTOSEAL-Roller/Brush is available in 5 gallon pails <br />Shelf Life: <br />12 months in unopened, original packaging. <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 2 of 2 <br />(updated 08/23/2016 BE/EK)</p>
