38 EPOXY-Multiuse Color Packs_012623.pdf
2 Pages
491 KB
Download
<h1>38 EPOXY-Multiuse Color Packs_012623.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>EPOXY-Multiuse Color Packs <br />Color Additives for EPOXY-Multiuse <br />CSI Div. 07 & 09 <br />07 18 00 Traffic Coatings <br />07 18 13 Pedestrian Traffic Coatings <br />09 67 00 Fluid-Applied Flooring <br />09 67 23 Resinous Flooring <br />09 96 13 Abrasion-Resistant Coatings <br />09 96 35 Chemical-Resistant Coatings <br />09 96 56 Epoxy Coatings <br />Product Description: <br />EPOXY-Multiuse Color Packs are premium quality color additives that are <br />specially designed and formulated for use with Aquafin’s EPOXY-Multiuse <br />Two-Component, Multipurpose Epoxy Floor Coating, Mortar Binder, and <br />Topcoat. <br />Typical Applications: <br />• Mix EPOXY-Multiuse Color Additives with EPOXY-Multiuse in the Clear <br />color. <br />Advantages: <br />• Provides 5 additional color options for EPOXY-Multiuse: <br />• Light Gray <br />• Dark Gray <br />• White <br />• Red <br />• Safety Yellow <br />• Conveniently packaged in pre-measured quantities for EPOXYMultiuse1.5 gal kits and 3 gal kits <br />Site Mock-up: <br />Aquafin recommends installation of a field sample of min. 100 ft² (9.29 <br />m²) at the project site or other pre-selected area as agreed to by owner’s <br />representative and applicator. <br />• Apply all materials to field sample area in the correct sequence. Follow <br />all manufacturer’s written instructions. <br />• Maintain field sample during construction for workmanship comparison. <br />Use field sample as standard for judging color and texture on remainder <br />of project. Do not alter, move, or destroy field sample until work is <br />completed and approved by owner’s representative. <br />Substrate Preparation: <br />Refer to the EPOXY-Multiuse Technical Data Sheet for information on <br />surface preparation. <br />Mixing: <br />• Epoxy resins are temperature sensitive and care should be taken to <br />condition all components (including the EPOXY-Multiuse Color Packs) to <br />between 70°F to 80°F (20°C to 26°C) for a minimum of 24 hrs. prior <br />to mixing and placement. <br />• Use chemical resistant gloves and goggles when mixing EPOXYMultiuse with EPOXY-Multiuse Color Packs. <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Physical and Technical Data <br />(Refer to EPOXY-Multiuse Technical Data Sheet) <br />• EPOXY-Multiuse Color Packs must be mixed with EPOXY-Multiuse in the <br />Clear color. See Chart on page 2 for guidance in ordering correct unit <br />quantities. <br />1. Do not alter mixing ratios. The volume mixing ratio is 2 parts component <br />A to1 Part component B (2A:1B). <br />2. Pre-mix the “A” and “B” components of EPOXY-Multiuse individually to <br />ensure all raw materials are dispersed uniformly. Mix a complete kit of <br />EPOXY-Multiuse in the proportions supplied. <br />3. Combine A and B components of EPOXY-Multiuse, and mix to a uniform <br />consistency (approx. 3 - 5 minutes) using a slow speed drill (approx. <br />300 to 450 rpm) with a jiffy mixing blade. Occasionally scrape the <br />bottom and sides of the container while mixing. Avoid entrapping air. Do <br />not mix in an up and down motion. <br />4. Add the EPOXY-Multiuse Color Pack and mix again (approx. 3 minutes) <br />to a homogenous streak-free color and consistency. <br />Once mixed, apply immediately! <br />Application: <br />Read all instructions thoroughly prior to installation. <br />Refer to the EPOXY-Multiuse Technical Data Sheet for all application <br />instructions. <br />Clean-up: <br />Clean tools and equipment with Methyl Ethyl Ketone (MEK), Xylene, or <br />similar product immediately after use. Cured material must be removed <br />mechanically. Soaking tools in an epoxy-stripper will help when <br />mechanical removal is necessary. <br />Limitations: <br />• EPOXY-Multiuse Color Packs are formulated for use only with Aquafin <br />EPOXY-Multiuse in the Clear color. Do not use EPOXY-Multiuse Color <br />Packs with other Aquafin products or with other brands of clear epoxy <br />coatings. <br />• Do not mix more material than can be used within 20 minutes [based on <br />75°F (24°C) and 50% RH]. <br />• Large mixed batches and high temperatures will significantly reduce the <br />pot life. <br />• High temperatures, high humidity and thicker applications will <br />significantly accelerate the cure time. Lower temperatures and/or low <br />humidity will extend the cure time. <br />• Contact Aquafin Technical Department or your local Aquafin <br />Representative for guidance in conditions outside the stated temperature <br />limits. <br />• Once containers have been opened, use material as soon as possible. <br />• Scratches in certain colors may appear white. <br />• Color may vary due to batch to batch variation, always “box” different <br />batches to avoid it. <br />Page 1 of 2</p> <p>(1/26 /23-EKJWAC)</p> <p>xy Color Guide</p> <p>EPOXY-Multiuse Color Packs <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Colors: <br />EPOXY-Multiuse Color Packs are available in: Light Gray, Dark Gray, <br />White, Red, and Safety Yellow. <br />Packaging: <br />EPOXY-Multiuse Color Packs are available in the following sizes: <br />LIGHT GRAY</p> <p>Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>Standard Epoxy Color Guide <br />MEDIUM GRAY</p> <p>• 1.5 lb color pack [for use with (one) 1.5 gal kit of EPOXY-Multiuse] <br />• 3 lb color pack [for use with (one) 3 gal kit of EPOXY-Multiuse] <br />NOTE: Sand aggregate is sold separately. <br />Shelf Life & Storage: <br />MEDIUM <br />•CHARCOAL <br />12 <br />months GRAY <br />in unopened, original packaging when stored <br />at <br />BLACK <br />temperatures between 40°F to 90°F (4°C to 32°C). <br />• Keep containers closed, store in a dry, cool place away from heat, <br />direct sun, sparks, open flame, and moisture. <br />• Protect material from freezing.</p> <p>oxy Color Guide</p> <p>For Professional Use Only.</p> <p>EPOXY-Multiuse Color Packs are available in the following colors: <br />BLACK <br />TAN</p> <p>WHITE <br />SAND BEIGE</p> <p>LIGHT GRAY <br />SAND <br />BEIGE <br />TILE <br />RED</p> <p>MEDIUM <br />GRAY <br />DARK <br />GRAY <br />RED</p> <p>CHARCOAL <br />RED GREEN <br />LEAF</p> <p>BLACK <br />LIGHT <br />TAN <br />SAFETY YELLOW</p> <p>LIGHT GRAY</p> <p>MEDIUM G</p> <p>CHARCOAL <br />WHITE</p> <p>BLACK</p> <p>TAN</p> <p>SAND BEIG</p> <p>Color Chart is a representation of the actual color only. Every effort has been made to reproduce these color samples as faithfully as possible. Color variations between <br />batches may exist. Colors may vary due to differences in surface texture, lighting, and methods of application. When ordering additional units, make sure you request the <br />same batch number. You will find the batch number on the product label. Not all colors are readily available. Some colors might require a minimum order quantity. Contact <br />Aquafin with questions regarding colors prior to ordering any materials or starting a project.</p> <p>EPOXY-Multiuse <br />Color Packs Unit <br />Quantities <br />the Clear color <br />TAN <br />SAND <br />BEIGE <br />BROWN <br />STONE with EPOXY-Multiuse <br />TILEin <br />RED <br />SAFETY YELLOW <br />Unit Quantity of EPOXY-Multiuse in the <br />Clear color</p> <p>Amount of EPOXY-Multiuse Color Pack <br />material required</p> <p>One 1.5 gal (5.7 L) kit of EPOXY-Multiuse</p> <p>1.5 lbs (0.7 kg)</p> <p>sentation of the actual color. Every effort has been made to reproduce these color samples as faithfully as <br />may exist. Colors <br />in surface texture, lighting, and 3methods <br />One 3may <br />gal vary <br />(11.4due <br />L) kittoofdifferences <br />EPOXY-Multiuse <br />lbs (1.4 of <br />kg)application. When <br />u use the same batch number. You will find the batch number on the product label. Not all colors are <br />1.5 gal <br />(5.7color <br />L) kitsavailability. <br />of EPOXY-Multiuse <br />3 lbs (1.4 kg) <br />hnical DataTwo <br />Sheets <br />for the</p> <p>Two 3 gal (11.4 L) kits of EPOXY-Multiuse</p> <p>RED BLUE <br />TILE RED <br />RICH <br />For approximate coverages, see EPOXY-Multiuse Technical Data Sheet.</p> <p>6 lbs (2.7 kg)</p> <p>RED</p> <p>Unit Quantity of EPOXY-Multise <br />Color Packs to order</p> <p>One 1.5 lb unit <br />One 3 lb unit <br />Two 1.5 lb units <br />LEAF GREEN</p> <p>Two 3 lb units</p> <p>SAFETY YE</p> <p>A• Tel: (847) 659-0300 • Fax: (847) 659-0310 • www.CrownPolymers.com • ©2017 All Rights Reserved</p> <p>Check our website for the latest version of the Technical Datasheet. <br />en made towww.aquafi <br />reproduce <br />these color samples as faithfully as <br />n.net <br />surface texture, lighting, and methods of application. When <br />e batch number on the product label. Not all colors are</p> <p>Page 2 of 2</p> <p>(1/26 /23-EKJWAC)</p>
