TDS-InjectPro-PumpFlush_062824.pdf
1 Page
40.7 KB
Download
<h1>TDS-InjectPro-PumpFlush_062824.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectPro-PumpFlush</p> <p>Non-flammable, pump flush for urethane grout pumps <br />CSI Div. 03 <br />03 64 00 Injection Grouting <br />Product Description: <br />InjectPro-PumpFlush is a non-flammable, maintenance solution for urethane <br />grout pumps, designed to clean and prime the pump and hoses before <br />and after each use, ensuring a moisture free pumping system. PumpFlush is <br />solvent free, non-hazardous, non-corrosive and compatible with all Aquafin <br />polyurethane grouts (InjectProECO-CombiGrout, InjectProECO-Cut, <br />InjectProECO-LV, InjectProECO-Polygel, InjectProECO-SEAL, InjectProECOSLV, InjectProECO-Soil, and InjectPro-SuperFAST). PumpFlush can be left in <br />the pump and hoses during storage between use. <br />Advantages: <br />• Zero VOC’s - meets LEED criteria <br />• 100% solids <br />• Non-flammable <br />• Non-corrosive <br />Physical Properties <br />State <br />Viscosity (ASTM D-1638) <br />Specific Gravity (ASTM D-1475)</p> <p>InjectPro-PumpFlush <br />Clear liquid <br />100 cps <br />0.97</p> <p>Flash Point (ASTM D-92)</p> <p>>400°F</p> <p>Boiling Point</p> <p>>480°F</p> <p>Packaging: <br />5 gallon pails or 50 gallon drums <br />Storage & Shelf Life: <br />Store in original sealed containers at temperature between 60°F – 90°F. <br />Opened containers must be handled properly to prevent moisture <br />contamination. <br />Limitations: <br />• P umpFlush is used to clean un-cured liquid urethane resins and has <br />limited effect on cured polyurethane. <br />•C <br /> lean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material such <br />as clay or vermiculite and transfer to appropriate waste containers. <br />Dispose of waste in accordance with federal, state and local <br />regulations.</p> <p>Note: <br />Proper application is the sole responsibility of the user. Applicators are <br />expected to follow ICRI and ACI guidelines as well as other applicable <br />industry standards. Aquafin personnel or representatives are not site <br />inspectors or construction project managers and therefore do not approve <br />surface preparation, mixing, or application of Aquafin products. Site visits <br />by Aquafin personnel or representatives are solely for the purpose of <br />making technical recommendations, not for providing supervision or quality <br />control. <br />General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time of <br />printing. Depending on specific applications, in particular regarding <br />substrates, processing and environmental conditions may affect final results. <br />Safety: <br />Refer to Safety Data Sheet (SDS). Use rubber gloves and goggles <br />during mixing and application. Avoid contact with eyes and skin. After <br />contact with skin, wipe up excess liquid then wash with plenty of soap and <br />water. In case of eye contact, rinse immediately with plenty of water and <br />seek medical advice. Do not ingest. <br />KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of labor, <br />which is proven to be defective. Our product recommendations are based on industry <br />standards and testing procedures. It is the buyer’s obligation to test the suitability of <br />the product for an intended use prior to using it. We assume no warranties written, <br />expressed, or implied as to any specific methods of application or use of the product. <br />We do not guarantee compatibility of Aquafin products with other brands. For this <br />reason, we strongly recommend application of a sample area at the jobsite to help <br />determine suitability with other products. AQUAFIN INC. MAKES NO WARRANTY <br />AS TO MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND <br />THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED. <br />AQUAFIN, INC. shall not be liable for damages of any sort including remote or <br />consequential damages, down time, or delay. Any claim for a defective product must <br />be filed within 30 days of discovery of a problem and must be submitted with written <br />proof of purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 1 of 1 <br />(updated 06/28/24-EKAC)</p>
