TDS-InjectProECO-RockSolid_022420.pdf
2 Pages
412 KB
Download
<h1>TDS-InjectProECO-RockSolid_022420.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectProECO-RockSolid</p> <p>Two component, high density polyurethane foam <br />CSI Div. 03 <br />03 64 00 Injection Grouting</p> <p>Physical Properties - liquid <br />(un-cured)</p> <p>Product Description: <br />InjectProECO-RockSolid is a two-component polyurethane system that can <br />be processed through low or high pressure injection equipment. When <br />properly mixed, the system will expand to approximately 25 times its initial <br />volume and cure to a durable, rigid, closed cell foam, resistant to water <br />and chemical attack. The closed cell foam will maintain its physical form <br />and is not subject to shrinkage due to wet/dry cycles. It is designed <br />to stop active water leaks and fill voids in concrete, gravel layers and <br />rock fissures. InjectProECO grouts are all environmentally friendly and <br />formulated without harmful phthalates or VOC’s. The system is comprised <br />of an “A” component (base resin) and a “B” component and is injected at <br />a 1:1 ratio. <br />Typical Applications: <br />Any concrete structure with larger volume water leaks such as: <br />• Water retaining structures, foundations, waste water treatment plants <br />& manholes, concrete dams, tunnels, parking garages, etc <br />Advantages: <br />• 100% solids, non-flammable <br />• Hydrophobic - can be used in wet and dry environments <br />• Very fast reaction time! ~30 seconds <br />• Can expand more than 25 times initial volume <br />• Excellent resistance and durability <br />• Non-hazardous shipping <br />• Non-toxic permanent seal <br />Reaction Times: <br />The reaction times vary based on temperature and exposure to water. <br />Typical reaction times ± 20-30 seconds: <br />Expansion Time <br />2 minutes <br />4 minutes </p> <p>Temperature <br />77°F (25°C) <br />50°F (10°C)</p> <p>Installation Procedures: <br />Refer to the InjectPro Grouting Guideline for full instructions. <br />Cartridges: <br />Use a dual component cartridge dispensing tool to ensure 1:1 mixing ratio <br />of product. After preping drill holes appropriately, remove the cap on top <br />of the cartridge. Attach the static mixing nozzle and ensure entire cartridge <br />is held upright until you are ready to start injecting. Insert the static mixing <br />nozzle into the drill hole and depress quickly with even strokes. Inject the <br />entire cartridge in one use, changing the static mixer once mixing is started <br />may not be possible due to the fast reaction time. <br />Plural Component Pump: <br />For larger volume grouting a plural component pump - such as the Aquafin <br />Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>InjectProECO-RockSolid Comp A</p> <p>InjectProECO-RockSolid Comp B</p> <p>Amber</p> <p>Dark Amber</p> <p>Viscosity (ASTM D-1638)</p> <p>~250 cps</p> <p>~1,500 cps</p> <p>Flash Point (ASTM D-92)</p> <p>>250°F</p> <p>>250°F</p> <p>Color</p> <p>Physical Properties - solid (cured)</p> <p>InjectProECO-RockSolid</p> <p>Compressive Strength (ASTM D-1621)</p> <p>~35 psi</p> <p>Tensile Strength (ASTM D-1623)</p> <p>~50 psi</p> <p>Shear Strength (ASTM D-732) <br />Water Absorption (ASTM D-2842)</p> <p>~25 psi <br />˂<2% (by volume)</p> <p>2K-Inject Pump - can be used. The pump must be set to ensure a 1:1 ratio <br />of component A : component B. Follow all pump manufacturers instructions <br />for proper procedures to prime pump and hoses as well as flushing static <br />mixing block and lines. <br />During injection, the grout will follow the path of least resistance. When <br />the material has stopped penetrating it will continue to expand against the <br />confines of the crack/joint and compress within itself, forming a very dense, <br />closed cell material stopping the leak. <br />Packaging: <br />InjectProECO-RockSolid is available in: <br />100 gallon kit: <br />50 gallon drum Component-A <br /> <br />50 gallon drum Component-B <br />10 gallon kit: <br />5 gallon pail Component-A <br /> <br />5 gallon pail Component-B <br />600 ml cartridges: <br />300 ml Component-A <br /> 300 ml Component-B <br />Storage & Shelf Life: <br />12 months when stored properly. Product is highly moisture sensitive. <br />Store in original sealed containers at temperature between 60°F – <br />90°F. Opened containers must be handled properly to prevent moisture <br />contamination. <br />Limitations: <br />• Temperature significantly affects viscosity. Protect material from excessive <br />heating and cooling prior to grouting to avoid affecting viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent water <br />coming in direct contact with resin - this will activate the reaction. Do not <br />warm above 90°F. <br />• Do not reseal containers of contaminated materials as it can create <br />pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material <br />Page 1 of 2</p> <p>(updated 02/24/20EK)</p> <p>InjectProECO-RockSolid <br />such as clay or vermiculite and transfer to metal waste containers. <br />Wash area with decontamination solution (5-10% solution of sodium <br />carbonate). Dispose of waste in accordance with federal, state and <br />local regulations. <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. Use rubber gloves and goggles during mixing and <br />application. Avoid contact with eyes and skin. After contact with skin, wipe <br />up excess liquid then wash with plenty of soap and water. In case of eye <br />contact, rinse immediately with plenty of water and seek medical advice. <br />Avoid breathing vapors. Use in well ventilated areas, or, in the case of <br />confined spaces, use self-contained respiratory protection. Do not ingest. <br />KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year from <br />the date of installation to be manufactured free of defects and to be consistent with its technical <br />properties as stated in our current Technical Data Sheet. This product must be used as directed <br />and within its stated shelf life. AQUAFIN INC. will replace or at our discretion refund the purchase <br />price of any product, excluding cost of labor, which is proven to be defective. Our product <br />recommendations are based on industry standards and testing procedures. It is the buyer’s <br />obligation to test the suitability of the product for an intended use prior to using it. We assume no <br />warranties written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR FITNESS <br />FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES <br />EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable for damages of any sort including <br />remote or consequential damages, down time, or delay. Any claim for a defective product must <br />be filed within 30 days of discovery of a problem, and must be submitted with written proof of <br />purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(updated 02/24/20EK)</p>
