TDS-InjectPro-SEAL 021219.pdf
2 Pages
72.7 KB
Download
<h1>TDS-InjectPro-SEAL 021219.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />f: 410-392-2324 <br />e: info@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectProECO-SEAL</p> <p>Low viscosity hydrophilic polyurethane grout <br />No harmful phthalates <br />CSI Div. 03 <br />03 64 00 Injection Grouting</p> <p>Physical Properties <br />ECO <br />FRIENDLY <br />TECHNOLOGY</p> <p>Product Description: <br />InjectProECO-SEAL is a water activated, flexible, hydrophilic polyurethane <br />injection grout with high tensile and bonding strengths. InjectProECO-SEAL <br />is designed for sealing leaking cracks or joints in below grade concrete <br />structures with continuous moisture exposure. InjectProECO grouts are <br />all environmentally friendly and formulated without harmful phthalates or <br />VOC’s. <br />Typical Applications: <br />Any concrete structure with water leaks such as water retaining structures, <br />waste water treatment plants and manholes, concrete dams, tunnels, <br />elevator pits and underground vaults. <br />Advantages: <br />• Zero VOC’s - meets LEED criteria <br />• 100% solids, non-flammable, non-toxic permanent seal <br />• Does not contain TDI or solvent <br />• Hydrophilic - seeks water in cracks <br />• Pumped as a single component <br />• Can expand more than 25 times initial volume <br />• Excellent adhesion, resistance and durability <br />• Non-hazardous shipping <br />Reaction Time: <br />When mixed with water at a 1:1 ratio the typical initial reaction time is 20 <br />seconds, with final reaction at approx. 3 minutes. <br />Installation Procedures: <br />Refer to the Aquafin InjectPro Grouting Guideline for full instructions. <br />InjectProECO-SEAL can be pumped as a single component product, or as <br />a dual component system with water. During injection, the grout will follow <br />the path of least resistance. When the material has stopped penetrating <br />it will continue to expand against the confines of the crack/joint and <br />compress within itself, forming a very dense, closed cell material stopping <br />the leak. <br />Packaging: <br />InjectProECO-SEAL Resin: 5 gallon pails and 50 gallon drums <br />Storage & Shelf Life: <br />Shelf life is two years when stored properly. Product is highly moisture <br />sensitive. Store in original sealed containers at temperature between 40°F <br />– 90°F. Opened containers must be handled properly to prevent moisture <br />contamination.</p> <p>Check our website for the latest version of the Technical Datasheet. <br />www.aquafin.net</p> <p>Liquid (un-cured)</p> <p>InjectProECO-SEAL Resin</p> <p>Color</p> <p>pale amber</p> <p>Viscosity (ASTM D-1638)</p> <p>approx. 300 cps</p> <p>Density (ASTM D-46590)</p> <p>approx. 70 lbs/ft3</p> <p>Flash Point (ASTM D-92)</p> <p>225°F</p> <p>Solid (cured) InjectPro-SEAL <br />Curing Time (1:1 water mix)</p> <p>approx. 20 sec. Initial Reaction <br />approx. 3 min. Final Reaction</p> <p>Expansion Rate</p> <p>400%</p> <p>Free Foam Density (ASTM D-3574)</p> <p>4.3 lbs/ft3</p> <p>Confined Density (ASTM D-3574)</p> <p>132 lbs/ft3</p> <p>Flash Point</p> <p>>300°F</p> <p>Limitations: <br />• Temperature significantly affects viscosity. Protect material from <br />excessive heating and cooling prior to grouting to avoid affecting <br />viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent <br />water coming in direct contact with resin - this will activate the reaction. <br />Do not warm above 90°F. <br />• Do not reseal containers of contaminated materials as it can create <br />pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material <br />such as clay or vermiculite and transfer to metal waste containers. <br />Wash area with decontamination solution (5-10% solution of sodium <br />carbonate). Dispose of waste in accordance with federal, state and <br />local regulations. <br />Note: <br />Proper application is the responsibility of the user. Field visits by AQUAFIN <br />personnel are for the purpose of making technical recommendations and <br />not for supervising or providing quality control on-site. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN.</p> <p>Page 1 of 2</p> <p>(updated 02/12/19-JW, SM)</p> <p>InjectProECO-SEAL <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />Page 2 of 2 <br />www.aquafin.net <br />(updated 02/12/19-JW,SM)</p>
