TDS-InjectProECO-SLV_072924.pdf
2 Pages
99.4 KB
Download
<h1>TDS-InjectProECO-SLV_072924.pdf</h1> <p>AQUAFIN Inc. <br />505 Blue Ball Rd. #160 <br />Elkton, MD 21921 <br />p: 410-392-2300 <br />e: info@aquafin.net <br />e: technical@aquafin.net <br />w: www.aquafin.net</p> <p>Technical Datasheet</p> <p>InjectProECO-SLV</p> <p>Hydrophobic, flexible, low viscosity polyurethane grout for stopping active leaks in cracks <br />No harmful phthalates <br />CSI Div. 03 <br />03 64 00 Injection Grouting</p> <p>Physical Properties <br />ECO <br />FRIENDLY <br />TECHNOLOGY</p> <p>Product Description: <br />InjectProECO-SLV is a closed cell, high performance, low viscosity <br />polyurethane injection grout designed for sealing hairline and very fine <br />leaking cracks in concrete. When it comes in contact with water, the grout <br />has high expansion (+2000% free foam) and quickly cures to a tough, <br />flexible, closed-cell polyurethane foam that is generally unaffected by <br />common corrosive environments and is not subject to shrinkage due to <br />wet/dry cycles. InjectProECO grouts are all environmentally friendly and <br />formulated without harmful phthalates or VOC’s. <br />The system is comprised of an “A” component (base resin) and a “B” <br />component (accelerator). The “B” component is used by the applicator to <br />adjust the set times for various job site specific conditions. <br />Typical Applications: <br />Stopping leaks in hairline and micro cracks in concrete structures such as: <br />• Water Retaining Structures, Concrete Dams, Tunnels, Elevator Pits, <br />Parking Garages, etc. <br />Advantages: <br />• Zero VOC’s - meets LEED criteria <br />• 100% solids, non-flammable, non-toxic permanent seal <br />• Hydrophobic - can be used in wet and dry environments <br />• Very low viscosity allows injection into hairline and micro cracks <br />• Accelerator and resin stable to -40°F. <br />• Pumped as a single component <br />• Excellent elongation creates a tight seal in moving cracks <br />• Adjustable reaction times <br />• Non-hazardous shipping <br />Reaction Times & Use of Accelerator: <br />The reaction time can be adjusted by the addition of accelerator “B” <br />into the base resin prior to pumping. The resulting profile is affected by <br />temperature and the amount of moisture present. <br />Typical Reaction Times <br />Percent (%) of <br />InjectProECO-ACCELERATOR-UNI</p> <p>Start of <br />Reaction</p> <p>End of <br />Reaction</p> <p>5%</p> <p>18 sec.</p> <p>1 min. 15 sec.</p> <p>7%</p> <p>11 sec.</p> <p>58 sec.</p> <p>8%</p> <p>11 sec.</p> <p>57 sec.</p> <p>10%</p> <p>11 sec.</p> <p>52 sec.</p> <p>Installation Procedures: <br />Refer to the current Aquafin Chemical Grout Handbook and please <br />contact Aquafin Technical Department or your local Aquafin <br />Representative for detailed grouting instructions. <br />Check our website for the latest version of the Technical Data Sheet. <br />www.aquafin.net</p> <p>Liquid (un-cured)</p> <p>InjectProECO-SLV <br />Resin</p> <p>InjectProECOACCELERATOR-UNI</p> <p>Color:</p> <p>Amber</p> <p>Clear</p> <p>Solids <br />(ASTM D2369):</p> <p>100%</p> <p>n/a</p> <p>Viscosity <br />(ASTM D1638):</p> <p>Density <br />(ASTM D4659):</p> <p>55 cps</p> <p>35 cps</p> <p>75 lbs. ft3 <br />(1.2 g/cm3)</p> <p>--</p> <p>>300°F</p> <p>225°F</p> <p>Flash Point <br />(ASTM D92):</p> <p>Physical Properties - solid (cured) InjectProECO-SLV <br />Density:</p> <p>74lbs/ft3</p> <p>Flexural strength:</p> <p>1200 psi</p> <p>Compressive Strength <br />(ASTM C109M):</p> <p>2400 psi</p> <p>Toxicity:</p> <p>non-toxic</p> <p>All data are average values obtained under laboratory conditions. Reaction times <br />tested in a 13.5 oz (400 ml) cup at 68°F (20°C).</p> <p>• Mix both the resin (Component A) and accelerator (Component B) <br />before combining. before combining. <br />• Pour the desired amount of InjectProECO-SLV Resin Component A into <br />a clean pail. <br />• Measure the appropriate amount of InjectProECO-ACCELERATOR-UNI <br />Component B and pour into the InjectProECO-SLV Resin, stirring until <br />adequately mixed. Never use more accelerator than recommended. <br />Excess accelerator will cause significant expansion that is prone to <br />shrinkage. <br />During injection, the grout will follow the path of least resistance. When <br />the material has stopped penetrating it will continue to expand against the <br />confines of the crack/joint and compress within itself, forming a very dense, <br />closed cell material stopping the leak. <br />Packaging: <br />InjectProECO-SLV Resin: 5 gallon pails (19 L) <br />InjectProECO-ACCELERATOR-UNI: 32 oz. container (0.95 L) <br />(5% dosage per 5 gallons (19 L) of resin. For 10% acceleration use 2 x 32 <br />oz. (2 x 0.95 L) <br />Storage & Shelf Life: <br />Shelf life is two years when stored properly. Product is highly moisture <br />sensitive. Store in original sealed containers at temperature between 40°F <br />Page 1 of 2</p> <p>(07/29/24-EKVBAC)</p> <p>InjectProECO-SLV <br />– 90°F. Opened containers must be handled properly to prevent moisture <br />contamination. <br />Limitations: <br />• Temperature significantly affects viscosity. Protect material from excessive <br />heating and cooling prior to grouting to avoid affecting viscosity. <br />• If using water baths to cool or heat pails avoid splashes to prevent water <br />coming in direct contact with resin - this will activate the reaction. Do not <br />warm material or packaging above 90°F. <br />• Do not reseal containers of contaminated materials as it can create pressure. <br />• Clean up spills with adequate ventilation and appropriate personal <br />protective equipment. Cover the spill area with absorbent material <br />such as clay or vermiculite and transfer to metal waste containers. <br />Wash area with decontamination solution (5-10% solution of sodium <br />carbonate). Dispose of waste in accordance with federal, state and <br />local regulations. <br />Note: <br />Proper application is the sole responsibility of the user. Applicators are <br />expected to follow ICRI and ACI guidelines as well as other applicable <br />industry standards. Aquafin personnel or representatives are not site <br />inspectors or construction project managers and therefore do not approve <br />surface preparation, mixing, or application of Aquafin products. Site visits <br />by Aquafin personnel or representatives are solely for the purpose of <br />making technical recommendations, not for providing supervision or quality <br />control.</p> <p>substrates, processing and environmental conditions may affect final results. <br />Safety: <br />Refer to SDS. For commercial use only. Avoid contact with skin and eyes. <br />Wear rubber gloves and safety goggles during mixing and application. <br />After contact with skin, wash with plenty of water. In case of eye contact, <br />rinse immediately with plenty of water for 15 minutes and seek medical <br />advice. KEEP OUT OF REACH OF CHILDREN. <br />LIMITED WARRANTY: AQUAFIN, INC. warrants this product for a period of one year <br />from the date of installation to be manufactured free of defects and to be consistent <br />with its technical properties as stated in our current Technical Data Sheet. This product <br />must be used as directed and within its stated shelf life. AQUAFIN INC. will replace <br />or at our discretion refund the purchase price of any product, excluding cost of <br />labor, which is proven to be defective. Our product recommendations are based <br />on industry standards and testing procedures. It is the buyer’s obligation to test the <br />suitability of the product for an intended use prior to using it. We assume no warranties <br />written, expressed or implied as to any specific methods of application or use of the <br />product. AQUAFIN INC. MAKES NO WARRANTY AS TO MERCHANTABILITY OR <br />FITNESS FOR A PARTICULAR PURPOSE AND THIS WARRANTY IS IN LIEU OF ALL <br />OTHER WARRANTIES EXPRESS OR IMPLIED. AQUAFIN, INC. shall not be liable <br />for damages of any sort including remote or consequential damages, down time, or <br />delay. Any claim for a defective product must be filed within 30 days of discovery of a <br />problem, and must be submitted with written proof of purchase.</p> <p>For Professional Use Only.</p> <p>General Information: <br />All details in particular to the suggestions for the processing and use of the <br />product is based on our present knowledge and experiences at the time <br />of printing. Depending on specific applications, in particular regarding</p> <p>Check our website for the latest version of the Technical Datasheet. Only the current version is legally binding - and only for the intended market. In cases of uncertainty contact <br />our technical department for further information before starting any applications. <br />www.aquafin.net <br />Page 2 of 2 <br />(07/29/24-EKVBAC)</p>
